How to measure card centering
Centering is four border widths and a little arithmetic. Here's how to measure them, how to work out the ratio, and where each method runs out of precision.
On this page
What you're measuring
Most cards have a printed border between the edge of the card and the artwork or frame. Centering compares the border on one side with the border on the opposite side: left against right, and top against bottom. A perfectly centered card has equal borders on opposite sides, which is written 50/50.
Each direction is read on its own, and the worse of the two is the one a grader's limit applies to. A card that is 50/50 top to bottom but 58/42 left to right is a 58/42 card.
The front and the back are measured separately too. Graders give the back much more room, which is covered in front vs back centering.
The arithmetic
Take the two borders in one direction. Divide the bigger one by the two added together, and multiply by 100. That's the first number of the ratio; the second is what's left of 100.
Example: left and right
The left border measures 3.0 mm and the right border 2.4 mm.
- Together: 3.0 + 2.4 = 5.4 mm.
- The bigger share: 3.0 / 5.4 = 0.556, so 55.6%.
- The ratio: 55.6/44.4.
That is past 55/45 by a little over half a point. At PSA, CGC and TAG, whose Gem Mint 10 front limit is about 55/45, this front would hold the card to a 9 on centering.
Example: top and bottom
The top border is 2.6 mm and the bottom 2.8 mm. Together 5.4 mm; the bigger share is 2.8 / 5.4 = 51.9%, so 51.9/48.1. That direction is comfortably inside 55/45. The card's front is still the 55.6/44.4 from the first example, because the worse direction counts.
How small the window is
On a border pair that adds up to about 5 mm, one point of ratio is about a twentieth of a millimetre on each side. Moving a tenth of a millimetre from one border to the other moves the ratio by roughly two points. That is why careful measurement matters most for a card that looks close to a limit.
Method 1: a ruler
A steel ruler marked in half millimetres is the simplest tool, and good enough to tell a 50/50 card from a 65/35 one.
- Lay the card flat on a dark surface under good light.
- Line the ruler's zero up with the card's edge, not the end of the ruler, which is often worn.
- Read where the border ends, looking straight down so the markings don't shift with your angle.
- Measure each border in the middle of its side, then again near each end if the border looks uneven.
Reading to half a millimetre leaves you a few points of ratio either way, so a ruler settles cards that are clearly centered or clearly not. For a card near 55/45, use one of the methods below.
Method 2: digital calipers
Calipers read to a hundredth of a millimetre, far finer than your eye can place the edge of a border. In practice the limit is where you set the jaws.
- Use the depth rod or the tips of the outside jaws, and close them gently: you're measuring printed ink, not squeezing the card.
- Steel jaws can mark a card's surface or dent an edge. Plastic calipers, or a sheet of clear film between card and jaw, are kinder.
- Measure each border two or three times and average. The spread between readings tells you how much to trust the result.
Method 3: a centering overlay
A centering overlay is a clear sheet printed with a card-sized outline and a grid or set of ratio lines. You lay it on the card, line the outline up with the card's edges, and see which line the border falls on. It's quick, needs no arithmetic, and is popular for sorting a stack of cards.
Its precision is set by how well the outline matches your card and how thin the printed lines are. Make sure the overlay is made for your card's size: Pokémon, One Piece, Magic and Lorcana cards are about 63 × 88 mm, but Japanese-size cards such as Yu-Gi-Oh! are smaller.
Method 4: a photo
A straight-on photo turns the card into pixels you can measure. On a sharp phone photo where the card fills most of the frame, a millimetre of border is many pixels wide, so the edge of the border can be placed more finely than with a ruler.
The catch is the angle. If the phone is tilted, the near side of the card looks bigger than the far side, and the ratio shifts with it. That's why a photo for centering is taken from directly above, and why a measuring tool should straighten the card before it measures. How to photograph a card for centering covers the rest.
Preslab does this part for you: it finds the card, straightens it, finds the border on each side and works out the ratios. It then draws the lines it used on your photo, so you can check where each one landed and drag any that sit off the border.
Cards with no border
A full-art or borderless card has no border to measure, so collectors look for something the layout prints at a fixed distance from the edge: a frame line, a text box, or a symbol in the corner. On a One Piece alt-art that's the cost circle and the colour hexagon; on Riftbound it's the circle and the gold frame. The game guides for One Piece and Riftbound go through those.
Tilted prints
Sometimes the artwork sits at a slight angle to the card's edges, so a border is wider at one end of a side than at the other. This is called a tilt or a diamond cut. Measure each border at both ends of its side, not just the middle, and use the worst pair. More on how that happens in why cards come out off-center.
Once you have a number
Compare it with the limit at the company you're sending to. For a 10 on the front, PSA, CGC and TAG each allow about 55/45, while Beckett's centering subgrade needs 50/50 for a 10. Centering by grading company has the full comparison.
Centering is one of four things a grade weighs, with corners, edges and surface. A card can be perfectly centered and still grade low.
Photograph the front and back. Preslab measures the centering and shows how high PSA, TAG, BGS, CGC and ACE let it grade. Free, and centering only.